Archives
now browsing by author
Physical and chemical properties test for powder coating films
Films ( Powder Coatings ) Physical Test Primary Test Equipment Characteristics Procedure (s) Film Thickness ASTM D 1186 Magnetic Film Thick Gauge, ASTM D1400 Eddy Current Induce Gauge Impact ASTM D2794 Impact Tester Flexibility ASTM D522 Conical or Cylindrical Mandrel Adhesion ASTM 2197 Balanced-Beam Scrape-Adhesion, ASTM D3359 Cross Hatch Cutting Device and Tape Hardness ASTM D3363 Calibrated Drawing Leads or Pencils Abrasion Resistance ASTM D4060 Taber Abrader and Abrasive Wheels ASTM D968 Edge Coverage ASTMRead More …
Anti-reflective coating is a type of optical coating applied to optical devices to reduce reflection
Anti-reflective coating or antireflection (AR) coatings are a type of optical coating applied to the surface of lenses and other optical devices to reduce reflection. This improves the efficiency of the system since less light is lost. In complex systems such as a telescope, the reduction in reflections also improves the contrast of the image by elimination of stray light. This is especially important in planetary astronomy. In other applications, the primary benefit is the elimination of the reflection itself, suchRead More …
What is Polyurea coating and Polyurethane Coatings
Polyurea coating is basically a two-component system based on Amine terminated prepolymer crosslinked with Isocyanate which forms the urea linkages. The crosslinking between reactive polymers take place at a rapid speed at ambient temperature. Normally this reaction does not require any catalyst. Since the Pot-life of such coating is within seconds; special type of Plural Component spray gun is require to carry out the application. The coatings can build up to 500 to 1000 microns of thickness in a singleRead More …
Breif introduction of Fusion bonded epoxy powder coating
Related Products : FBE Powder Coating Related Articles: FBE Powder Coating Fusion bonded epoxy coating, also known as fusion-bond epoxy powder coating and commonly referred to as FBE coating, is an epoxy based powder coating that is widely used to protect steel pipe used in pipeline construction, concrete reinforcing bars (rebar) and on a wide variety of piping connections, valves etc. from corrosion. FBE coatings are thermoset polymer coatings. They come under the category of ‘protective coatings’ in paints andRead More …
What is Moisture-cured polyurethane
Moisture-cured polyurethane is one-part polyurethane that its cure is initiatedly environmental moisture. The moisture-curable polyurethane is mainly consists of isocyanate-terminated pre-polymer. Various types of pre-polymer can be used to provide required property. For instance, isocyanate-terminated polyether polyols are used to provide good flexibility due to their low glass transition temperature. Combining soft segment, such as polyether, and hard segment, such as polyurea, provides good hardness and flexibility of coatings. Moreover, the properties are also controlled by selecting types of isocyanatesRead More …
The binder,referred to as the vehicle,is the actual film forming component of paint
The binder, commonly referred to as the vehicle, is the actual film forming component of paint. It is the only component that must be present; other components listed below are included optionally, depending on the desired properties of the cured film. The binder imparts adhesion, binds the pigments together, and strongly influences such properties as gloss potential, exterior durability, flexibility, and toughness. Binders include synthetic or natural resins such as acrylics, polyurethanes, polyesters, melamine resins, epoxy, or oils. Binders canRead More …
Masking tapes to cover the finishing needs during coating process
There is a full range of masking products to cover the finishing needs, masking caps, plugs and hooks to tapes and masking dots. Masking tape is a type of pressure sensitive tape made of a thin and easy-to-tear paper, and an easily released pressure sensitive adhesive. It is available in a variety of widths. It is used mainly in painting, to mask off areas that should not be painted. The adhesive is the key element to its usefulness, as itRead More …
Differential scanning calorimetry for coating curing
Via the DSC technique it can be verified if the coating is sufficiently cured or not. The DSC is a technique verifying how much energy is needed to have no temperature difference between the substance in test phase and the referential material, determined in according to time and temperature, when two specimen are submitted to identical temperature conditions in a controlled warm or cooled environment. First of all, the thermal history of the material is disturbed by the fast coolRead More …
Test Standard for weathering resistance of powder coatings
Resistance to mortar According to the standard ASTM C207. A specific mortar will be brought in contact with powder coating during 24h at 23°C and 50% relative humidity. Accelerated ageing and UV durability (QUV) This test in the QUV-weatherometer consists of 2 cycles. The coated testpanels are 8h exposed to UV-light and 4h to condensation. This is repeated during 1000h. Every 250h the panels are checked. Herewith the coating is tested on colour- and gloss retention. Saltspraytest According to theRead More …
General Mechanical properties of powder coatings
Cross-cut Test (adhesion) According the standards ISO 2409, ASTM D3359 or DIN 53151. On the coated test panel a cross-cut (# : indentations in the form of a cross and parallel to each other with a mutual distance of 1 mm or 2 mm) is made on the metal. A standard tape is put on the cross-cut. The cross-cut is valued through the quantity of the detached film after removing the tape. Flexibility A coated standard test panel is foldedRead More …
D5 Creation